Myro Control   |   Myro:Air   |   Myro:Bridge   |   Myro:Home   |   Contact   |   Support

Recent Posts

Pages: 1 2 3 [4] 5 6 ... 10
31
Feature Request / Sonos auto pause (Russound)
« Last post by SeppeR on September 28, 2015, 06:23:23 am »
Hi,

It should be handy if myro:bridge detects when a user disables a zone, auto pause sonos if no other zone is playing the sonos source, or is this impossible?

Friendly regards,

Seppe
32
General Discussion / Re: Myro stops controlling KD matrix
« Last post by techelec on March 27, 2015, 12:01:38 pm »
OK.  Thanks a bunch Danny!  will do the support ticket.
33
General Discussion / Re: Myro stops controlling KD matrix
« Last post by Myro Control on March 27, 2015, 09:44:42 am »
Just another question first.  This system will work all day just fine, maybe two days, but at some point the video switching will cease.   I went there today and cycled power simultaneously to all components, still no switching.  If I "reboot" the bridge all is well again switching sources, etc.   Is there a way to make a power cycle a "reboot?"  It seems as thought the bridge needs to be rebooted occasionally to work. Can an issue with the RNET data cause this?   

Btw, there is no internet connection, but a router is connected and the Myro has the latest firmware for offline mode.  I cleared the Myro and reflashed it again last week with the same firmware.  It appears as though I have a Bridge that is going awry, but I want to make sure that the RNET data cannot corrupt it???  Reason I ask it that I am having issue with a command that sends  "PLAY"  to the Bluray player to wake it up when that source is selected.

You should never have to reboot a Myro:Bridge that has the Matrix Firmware installed, once it's up and running.   So the issue you are having could be related to EMI or something else.  I'd rather replace the unit than have you spend time troubleshooting this.   I can advanced ship a unit if needed as well.  Please create a support ticket with address and we'll get a unit shipped out.

Thanks!
34
General Discussion / Re: Myro stops controlling KD matrix
« Last post by techelec on March 25, 2015, 04:49:53 pm »
Just another question first.  This system will work all day just fine, maybe two days, but at some point the video switching will cease.   I went there today and cycled power simultaneously to all components, still no switching.  If I "reboot" the bridge all is well again switching sources, etc.   Is there a way to make a power cycle a "reboot?"  It seems as thought the bridge needs to be rebooted occasionally to work. Can an issue with the RNET data cause this?   

Btw, there is no internet connection, but a router is connected and the Myro has the latest firmware for offline mode.  I cleared the Myro and reflashed it again last week with the same firmware.  It appears as though I have a Bridge that is going awry, but I want to make sure that the RNET data cannot corrupt it???  Reason I ask it that I am having issue with a command that sends  "PLAY"  to the Bluray player to wake it up when that source is selected.
35
General Discussion / Re: Myro stops controlling KD matrix
« Last post by Myro Control on March 20, 2015, 02:39:12 pm »
Do you want me to ship you another unit?   If so, please create a support ticket, http://www.myrocontrol.com/support and we'll ship one out.
36
General Discussion / Re: Myro stops controlling KD matrix
« Last post by techelec on March 18, 2015, 03:48:16 pm »
Yes.  It is a KD 4 x 4 CSX and the serial output is working, but only as long as my laptop is connected to the MYRO USB port, not with any of the 5 volt USB power supplies that I have tried, including the original one that came with it.  So... it all works, I just have to have my laptop feeding USB power and enable the debugging tool.  I  cleared the unit and reflashed the firmware as well.

Yes, I can email you when I am back on that job again and we can speak, but it won't be till next week.  I will give you some notice and realize you are 3 hours different.  Thanks a lot.
37
General Discussion / Re: Myro stops controlling KD matrix
« Last post by Myro Control on March 18, 2015, 11:02:18 am »
Can you provide us with the model of KD matrix you are trying to control? 

Also, can you verify you can control the KD matrix via a PC via Serial?

We can setup a time to chat on the phone, could be quicker to troubleshoot.  Create a support ticket: http://www.myrocontrol.com/support

Thanks!
38
General Discussion / Myro stops controlling KD matrix
« Last post by techelec on March 17, 2015, 05:25:32 pm »
The Myro will not output serial data to the KD matrix, but if I connect my PC to the USB port and use the debugging tool, it outputs perfectly.  I have tried two different power supplies and I can see that the power is on, but it wants to see my PC connected instead of a power supply of 5 vdc.  Any ideas?  I have the firmware that allows for offline mode installed and am only using a router for IP, as it has no internet connection. (on a boat) Thanks.
39
Tech Notes / FAQ / Re: Crestron Control Module
« Last post by vincen on March 17, 2015, 09:25:27 am »
AirPlay protocol does not allow full control with Navigation.   As for the full IP protocol, we have not released it yet, we recommend RS232 as that provides everything you need and has been more reliable than using the IP method.
First I'm sorry but IP control can be as reliable than RS-232 if it's correctly programmed on both side of link !

Second RS-232 is not enough as it exists with your protocol as we need to be able to interact with the source to select some songs, playlists which is not possible right now with your RS-232 protocol right ? Any timeframe when IP control would be avalaible or is it on hold ?

Thanks
40
Tech Notes / FAQ / Re: Crestron Control Module
« Last post by Myro Control on March 17, 2015, 09:18:57 am »
Some news about full control with navigation ? as I find nothing about it anywhere on website and no way to find full IP protocol promised one year ago....

Hi Vincen,

AirPlay protocol does not allow full control with Navigation.   As for the full IP protocol, we have not released it yet, we recommend RS232 as that provides everything you need and has been more reliable than using the IP method.
Pages: 1 2 3 [4] 5 6 ... 10