Myro Control   |   Myro:Air   |   Myro:Bridge   |   Myro:Home   |   Contact   |   Support

Recent Posts

Pages: [1] 2 3 ... 10
1
Firmware / Re: Matrix Firmware v1.3.25
« Last post by Myro Control on September 09, 2016, 07:28:17 am »
hi

i need some support on a Kramer 6x6 matrix to russound RNET and myro where do i find the firmware

Please create a support ticket at www.myrocontrol.com/support

Thanks!
2
Firmware / Re: Matrix Firmware v1.3.25
« Last post by Derick AV on September 06, 2016, 04:00:51 am »
hi

i need some support on a Kramer 6x6 matrix to russound RNET and myro where do i find the firmware

3
Firmware / Re: Matrix Firmware v1.3.25
« Last post by Myro Control on April 22, 2016, 11:22:11 am »
Hi, please email support or create a support ticket and we'll send it right over.
4
Firmware / Re: Matrix Firmware v1.3.25
« Last post by nelsonmelean on April 20, 2016, 01:49:29 pm »
PLease send me the last update firmware for myro bridge, Rnet to video matrix
5
General Discussion / Re: Myro bridge reporting "finding zoneplayer"
« Last post by Myro Control on November 22, 2015, 09:30:11 am »
@darobin77 -- please create a support ticket and we'll be able to step you through.

Typically, if it stays on, "Finding Zone Player" it means that it was once paired and it cannot find the zone player.  The quick and easy solution is to go to the internal Myro:Bridge webpage an select the same RNET ID but the one lower in the dropdown list (it will make sense).  Then after the page reloads, press the reboot button on the back of the Myro:Bridge.

That should put it back into the "Add a Sonos Component..." message where you can pair it again.  To do this, press the "Volume Up" and "Mute" buttons on the Sonos Connect to put it into discovery mode.
6
General Discussion / Re: Myro bridge reporting "finding zoneplayer"
« Last post by darobin77 on November 10, 2015, 03:52:38 pm »
Hi I'm having the same issue. Any other solutions ?
7
Tech Notes / FAQ / Re: Russound MCA-5 HDMI Source
« Last post by Myro Control on October 06, 2015, 04:30:14 pm »
Yes, you will need keypads for the Russound for the easiest installation.  If you don't have keypads, then the via Matrix is the way to go.
8
Tech Notes / FAQ / Re: Russound MCA-5 HDMI Source
« Last post by jayday on October 05, 2015, 06:40:32 am »
Thanks.
Using the Russound IR, are keypads required? Have you seen installations using only the iPad app to control each zone with perhaps an external IR connection to the MCA common IR port?
9
Tech Notes / FAQ / Re: Russound MCA-5 HDMI Source
« Last post by Myro Control on October 04, 2015, 07:10:24 pm »
Hi!

Either way, I prefer IR control via the Russound, but there are pros/cons to each. 
10
Tech Notes / FAQ / Re: Russound MCA-5 HDMI Source
« Last post by jayday on October 02, 2015, 01:44:53 pm »
Installing Keydigital KD-4x4CSX to Russound MCA-5.  What is the best practice to install the IR control?  Should it be on the Russound or Keydigital?  I am using iPad app to control most zones and not keypads.
Pages: [1] 2 3 ... 10